Main body of slipper: (Make 2)
Cast On 10 (12, 16) stitches with A.. Lay anchor yarn.
Knit in Stockinette for 2 rows.
Next row: You will extend the stitches to include the toe and foot.
Weave in Stockinette for a total of 22 (26,30) stitches.
Lay a new anchor yarn over the new stitches.
Hook over original stitches. The new stitches only have one loop and you can’t hook them until the
Knit in Stockinette for a total of 20 (24, 28) rows. (for wider feet, Knit additional rows. Each 2
rows will add approximately ˝ inch to width.)
Bind Off for the foot area:
(You will bind off the stitches that were added.)
Starting at end opposite the attached yarn, bind off with crochet hook by pulling 1 loop thru 1
loop. When you get to the original 10 (12, 16) needles, lay the last loop on the crochet hook onto
the end needles. This will create a double loop on the last needles.
Knit the original needles for 2 rows. When you get to the end needles with extra loop, be sure to
lift the 2 bottom loops over.
Bind Off the remaining stitches starting at end opposite the yarn attachment.
Bind Off both sets of anchor yarns at opposite edge. Set the slipper aside.
Knit 2nd slipper just like this one.
Toe/top of slipper: (Make 2)
Cast On 6 stitches in Stockinette Stitch. All sizes.
Knit 6 (8, 8) rows
Decrease 1 stitch each end of board (both sides of board)
You now have 4 sts for all sizes.
Knit in Stockinette for 14 (16, 18) additional rows.
Bind Off with crochet hook.
Knit additional toe/ top slipper just like this one.
Bind Off at anchor yarn.
Sewing the Slipper together.
Fold slipper lengthwise. The shorter end is the toe side. The taller end is the cuff side.
Mark the center of the toe end with piece of yarn.
One extra piece (toe/top) will be sewn in between the 2 sides of the top of the slipper. The wider
end is the toe end. Match the center of toe end with center of toe on slipper. Slip a piece of yarn
thru the 2 pieces at matching centers.
Start sewing the top of slipper to one side of slipper (main piece). You will be starting at point
where the slipper extends for the cuff. Ease the 2 pieces together as you sew so that the seams are
even and the toe is rounded. Sew to the center marker.
Sew the other side of slipper to the slipper toe/top, easing the 2 pieces together, ending at the
center marker. This will complete the top of slipper.
Sew the heel from slipper bottom to top at cuff.
Making the Cuffs: (Make 2)
Now that your slipper is sewn together except for the cuff, you can get an exact measure for how
long to make each cuff so that it fits the slipper. Measure with soft measure tape around the cuff
area and add ˝”. This should be approximately 12 (13, 14) inches.
Cast On 6 Stitches using B. Lay anchor yarn.
Knit in Stockinette Stitch for 34 (36, 38) rows or until the piece measures the same length as your
measurement around the cuff area.
Bind Off at anchor yarn.
Sewing the Cuffs:
The ends of the cuff will match with the cuff area starting where the slipper top begins. Match
the 2 side edges, laying the cuff around the slipper. Secure the ends to the slipper with a crochet
hook or similar long needle to hold in place as you sew.
Use the invisible stitch to sew one edge of cuff to edge of slipper. You should sew the slipper
about ˝ inch from top. Sew the cuff using very edge stitch.
Now, roll the opposite edge of cuff over the top of slipper, matching the corners. Sew in place.
You may want to turn the slipper inside out to sew this side.
You may close up the ends of the cuff in your sewing or use it as a casing for a drawstring.
(Our sample has the ends closed up. If you choose the casing, your slipper will take on the
appearance of moccasins, a nice variation.