This site is currently in beta mode. Please contact us with your comments or suggestions.

Motif Afghan Crochet-Along: The Finish Line

We're almost there!

I've finished making all my motifs and, since I was joining them as I did the last round of each, I don't have any additional joining to do. However, many of you chose to wait until now to join your motifs, a method I often choose. Since I know at least ten ways to do so, I have a choice of options at this point. Sewing motifs together with a tapestry needle and whip stitch is a non-starter for me. Meaning: I never do it. Waaaaaaay too slow and finicky.

Single crochet seam

This seam can be done either on the wrong side or the right side of the piece. It is a sturdy yet flexible join. It makes a nice ridge, which can be used as a design element to frame the motifs. Some people think the ridge looks "wrong"; I think it's a lovely three-dimensional element that adds interest, and I often choose to put it on the right side. I've used a contrasting color yarn so that the seam shows up.

To work a single crochet seam on the right side, hold the motifs with wrong sides together and sc through the adjacent stitches and chain-spaces on both motifs.

In this design, I would probably work a bunch of short seams to create long strips of hexagons, then join those long strips with long zigzag-shaped seams lengthwise down the afghan. You'll have to figure out the best way to handle the corners when 3 motifs meet.

On my sample, I joined the 3rd motif to the 2nd one from chain-spaces to chain-spaces, then chain 1, and joined the same chain-space of the 3rd motif to the next chain-space of the 1st motif, continuing along that edge to the next corner. (This will make more sense when you have a lot of pieces in your hand and you try it yourself!)

Here's what the sc seam on the right side looks like:

Here's what it looks like on the wrong side:

Note that this last photo shows more or less what the seam would look like if you worked it on the wrong side. To work a single crochet seam on the wrong side, hold motifs with right sides together and sc through the adjacent stitches on both motifs.

Single-crochet/chain seam
This join is a bit looser and more flexible than the single crochet seam. Again, it can be done either on the right side or the wrong side of the work. Instead of working into every stitch and chain-space as shown above, join with a sc at the corners, *ch 1, skip 1 pair of stitches, sc through next pair of adjacent stitches; repeat from * across the edge to the corner. As for the single crochet seam, you'll have to experiment a bit to figure out how best to handle the corners where 3 motifs join. It may require a chain 1, 2 or 3 at the corner to lie flat.

Single Crochet Join on Final Round
My final suggestion is a hybrid of the join-as-you-go method that I showed you before. In this method, add an additional round of single crochet around each motif, joining as you go.

On the first motif, work a complete round of single crochet, placing 1 sc in each dc and (sc, ch 1, sc) in each corner space. Fasten off.

On the second motif, work a round of sc to the next-to-last corner. Sc in corner, ch 1, join that chain in the adjacent chain from the first motif (as described here), sc in same chain-space of current motif, join that sc to the adjacent sc from the first motif, and so on.

As you work, you may find that you need to put 2 or 3 chains in the corner to make the corners tidy—don't be afraid to play around with it to get the perfect technique for your situation.

Which of these (or any other methods) is best? By now (hopefully), you'll know what my answer is: only you can decide what's best in your situation. Play with variations on these joins and decide which one you think is just right for your needs. For example, you may find that the join-only-in-the corner method that I showed you in a previous post is quick, but not sturdy enough for hard use, or you may think it gives the perfect lacy look you prefer.

Weaving in ends

Everyone has just been itchin' for me to talk about weaving in ends. Your time has finally come. In an earlier post, I wrote about working over yarn ends as I create new stitches. I will do often do this, but I find that in an item that gets handled a lot, like an afghan, the worked-over ends are not secure enough. I prefer to weave in all my ends with a tapestry needle for the final finish.

Yes, this is tedious. It's not nearly as much fun as stitching cute little hexagons. However, it IS a critical part of the afghan-making process. A couple of nights in front of the TV should do it.

I use a blunt-tip tapestry needle with a big enough eye so that I can easily thread it, yet not so big that it has trouble fitting through the stitches. You do know this trick for threading a tapestry needle, don't you?

Weave the yarn tail in a couple of different directions through the back of the same-color stitches. The more different directions you go in, the more secure your tail will be.

Some people choose to use a sharper needle and actually skim through the back of the stitches, splitting the yarn. If you have a latch hook, you might find it easier to use it to weave in your ends.

A Finishing Round
Once I had all my ends woven in, I used a steam iron to carefully block the entire afghan. You may have heard that blocking is not necessary with acrylic yarn, but I find that blocking gives a finished look to any crocheted piece. I was careful to use the lowest steam setting on my iron, and I NEVER touch the iron to the fabric, as it it is possible to "kill" acrylic yarn and thus alter its drape. I just skimmed the iron over the afghan, keeping it about 2" above the fabric.

Then I decided that a final round of single crochet would be a nice touch and would help strengthen and secure the edges. I worked 1 sc in each dc around, putting (sc, ch 1, sc) in each "outer" chain-space corner, and 1 sc in each "inner" chain-space corner.

Final Results

Can you see where I threw in a few off-pattern motifs to keep it interesting? Adding another color would have been fun, as well.

The finished size is about 37" x 53". That's reasonably close to what I predicted. It is a bit small for a traditional-sized afghan, but I could easily have added motifs to make it larger. As it is, I decided it's a perfect lap-ghan size to throw over my legs while I'm crocheting.

Also as predicted, the weight of the finished afghan indicated I used a total of about 8 balls of yarn. The breakdown of colors was about 5 balls of Taupe, 3 balls of Linen and 2 balls of Cranberry. (Yes, these add up to more than 8 balls, because the final ball of each color was not used up.)

It's Just the Beginning

Those of you who have stuck with me this far, congratulations! I hope I've been showing you things you didn't know before, and that you have been having fun and gaining confidence while working along with me. I haven't been able to share half of what I know and love about crocheting; if you want to learn more, read more here at the Lion Brand website, refer to The Crochet Answer Book and Beyond the Square Crochet Motifs, and take classes. All my fellow crochet teachers and I are anxious to share our love of the craft with you.

I hope you'll keep stitching and striving to grow your knowledge while enjoying what you are doing. No stress, no "wrongs", just opportunities to learn. I'll be hanging out here at the Lion Brand Notebook for another week or so to answer questions and respond to comments. After that, you'll still be able to find me on the Ravelry CAL group or on my website.

Stitch On--and HAVE FUN!

Related links:

Tagged In: